GPPS Zurich18: Proceedings

  1. An Enhanced Compressor Sub-Idle Map Generation Method Luis E. Ferrer-Vidal, Vassilios Pachidis, Richard J. Tunstall (2018), DOI: ,

    Download Paper


  2. Effects of Secondary Air Removal on the Aerodynamic Behaviour of Compressor Cascade Flow Thorben Aufderheide, Jens Friedrichs, Bernd Becker (2018), DOI: ,

    Download Paper


  1. Towards an Integrated Approach for Micro Gas Turbine Fleet Monitoring, Control, and Diagnostics Ioanna Aslanidou, Valentina Zaccaria, Moksadur Rahman, Mark Oostveen, Tomas Olsson, Konstantinos G. Kyprianidis (2018), DOI: ,

    Download Paper


  2. Dynamic Modeling of an Industrial Gas Turbine in Start-Up Mode Using Monitoring Data Abdollah Mehrpanahi, Ali Ghorbanifar, Ali Hamidavi, Hero Salahifard (2018), DOI: ,

    Download Paper


  1. Enabling efficient and low emissions deep part load operation of combined cycles and combined heat and power plants with external Flue Gas Recirculation Johan Steimes, Sikke Klein, Marco Persico (2018), DOI: ,

    Download Paper


  2. Influence of Multiple Degrading Components on Gas Turbine Fuel Cell Hybrid System Lifetime Valentina Zaccaria, Alessandra Cuneo, Alessandro Sorce (2018), DOI: ,

    Download Paper


  3. Modeling, Analysis and Multi-Objective Optimization of Adding Recuperator on Techno-Economic Properties of Mgt-70 Gas Turbines A. Pourjafar, A. Mehrpanahi, S. Nikbakht Naserabad, H. Salahifard (2018), DOI: ,

    Download Paper


  4. Impact of Gas Turbine Cyclic Operation on Engine Aging – an Investigation of the GT24/GT26 Fleet Moritz Lipperheide, Frank Weidner, Martin Gassner, Stefano Bernero, Manfred Wirsum (2018), DOI: ,

    Download Paper


  5. Performance Analysis and Prediction of Compressor Fouling Condition for a Twin-Shaft Engine Shaojuan Geng, Bing Bai, Hongwu Zhang, Jichao Li, Chaoqun Nie (2018), DOI: ,

    Download Paper


  1. Experimental Investigation of the Sealing Performance of a New Adaptive Seal System Laura Beermann, Hans-Jörg Bauer, Corina Schwitzke, Julius Wilhelm (2018), DOI: ,

    Download Paper


  2. Roughness effects on flow and heat transfer in a ribbed duct considering additive manufacturing Edward Kilpatrick, Sung in Kim (2018), DOI: ,

    Download Paper


  3. Shape Optimization in Low-Order Thermoacoustic Networks José G. Aguilar, Matthew P. Juniper (2018), DOI: ,

    Download Paper


  4. Nozzle Pressure Side Film Cooling and Endwall Phantom Cooling Kevin Liu, Luzeng Zhang, Michael D. Fox (2018), DOI: ,

    Download Paper


  5. Heat Transfer Coefficients in a Turbocharger With and Without Boiling Thomas-Sebastian Gier, Thomas Biesinger, Henning Eickenbusch (2018), DOI: ,

    Download Paper


  6. Investigating the Change of Discharge Behaviour of Gas and Liquid by Means of Analytical and Numerical Approaches Laura Cordes, Lisa Hühn, Corinna Schwitzke, Hans-Jörg Bauer (2018), DOI: ,

    Download Paper


  7. The Influence of Inlet Corner Shape on the Static and Dynamic Performance of an Annular Pressure Seal Luis San Andrés, Jing Yang (2018), DOI: ,

    Download Paper


  1. Parametric Assessment of a Surge Severity Coefficient Enrico Munari, Mirko Morini, Michele Pinelli, Klaus Brun, Sarah Simons, Rainer Kurz (2018), DOI: ,

    Download Paper


  2. Performance Degradation Effects in Modern Industrial Gas Turbines Dan Burnes, Rainer Kurz (2018), DOI: ,

    Download Paper


  1. Mechanical Design of a 3D Printed, Semi-Shrouded, Centrifugal Compressor Impeller for Supercritical Co2 Application Fang Li, Robert Pelton, Sewoong Jung (2018), DOI: ,

    Download Paper


  1. Development of Hot Standby Mode for flexible Steam Turbine Yevgen Kostenko, David Veltmann (2018), DOI: ,

    Download Paper


  2. Modelling of Angle Controlled Engagement for a Single Shaft CCPP with Mechanically Decoupled LP Turbine for Maximum Heat Extraction Dr. Carmen Stüer, Dr. Gerta Zimmer (2018), DOI: ,

    Download Paper


  3. Fast Numerical Calculation Approaches for the Modelling of Transient Temperature Fields in a Steam Turbine in Pre-Warming Operation with Hot Air Piotr Łuczyński, David Erdmann, Dennis Többen, Manfred Wirsum, Klaus Helbig, Wolfgang Mohr (2018), DOI: ,

    Download Paper


  1. Influence of Aerodynamic Damping on Torsional Vibrations of Turbine Shafts Christopher E. Meinzer, Christian Keller, Joerg R. Seume, Olga Korolova, Bernd Ponick (2018), DOI: ,

    Download Paper


  2. Modelling the Rubbing Process in Labyrinth Seals Oliver Munz, Corina Schwitzke, Hans-Jörg Bauer, Sarah Welzenbach, Tim Fischer, Sonun Ulan kyzy (2018), DOI: ,

    Download Paper


  1. Impact of Purge Flows on the Unsteady HPT Stator-Rotor Interaction Stefan Zerobin, Andreas Marn, Franz Heitmeir, Emil Göttlich, Andreas Peters (2018), DOI: ,

    Download Paper


  2. Aerodynamic Investigation of an Embedded Uhbrengine Concept Constance Heykena, Jens Friedrichs (2018), DOI: ,

    Download Paper


Our location

With team members spread across the globe, the core team is based in Zurich Switzerland.

m

Landis + Gyr-Strasse 1, 6300 Zug